Echo Blower 99944200490 User Manual

Power Blower Attachment  
Operator's Manual  
MODEL  
99944200490  
MODELS USED ON:  
SRM-2100SB/2400SB  
SRM-210SB/211SB  
SRM-225SB  
SRM-260SB/261SB  
PAS 2100/2400  
PAS 210/211  
PAS-225/PAS-225VP  
PAS 230/231  
PAS 260/261  
PAS-2601  
PAS-265  
WARNING  
Read rules for safe operation and instructions carefully. ECHO provides an Opera-  
tor's Manual and a Safety Manual for Pro Attachment Series power source or Split  
Boom Trimmer. Those manuals and this manual must be read and understood for  
proper and safe operation, otherwise serious personal injury may result.  
X770001460  
09/10  
X7702095400  
 
Po w e r Bl o w e r At t A c h m e n t  
oP e r A t o r 's mA n u A l  
3
sa f e t y  
m a n u a l s a f e t y s y m b o l s a n d Im p o r t a n t In f o r m a t Io n  
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre-  
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to  
you.  
CIRCLE AND SLASh SyMBOL  
DANGER  
This symbol means the specific action  
shown is prohibited. Ignoring these prohi-  
bitions can result in serious or fatal injury.  
The safety alert symbol accompanied by the word  
“DANGER” calls attention to an act or condition  
which WILL lead to serious personal injury or  
death if not avoided.  
NOTE  
WARNING  
This enclosed message provides tips for use, care and  
maintenance of the unit.  
The safety alert symbol accompanied by the word  
WARNING” calls attention to an act or condi-  
tion which CAN lead to serious personal injury or  
death if not avoided.  
IMPORTANT  
The enclosed message provides information neces-  
sary for the protection of the unit.  
CAUTION  
The safety alert symbol accompanied by the word  
“CAUTION” calls attention to an act or condition  
which may lead to minor or moderate personal  
injury if not avoided.  
In t e r n a t Io n a l s y m b o l s  
Symbol  
Symbol  
description/application  
Symbol  
description/application  
Symbol  
description/application  
Symbol form/shape  
Symbol form/shape  
Symbol form/shape  
Symbol form/shape  
description/application  
Read and understand  
Operator's Manual.  
Ignition  
ON/OFF  
Fuel and oil mixture  
Finger Severing  
Emergency stop  
Wear eyes, ears and  
head protection  
Carburetoradjustment  
- Low speed mixture  
Primer bulb  
Wear hand  
protection. Use  
two handed.  
Hot  
Surface  
Carburetor adjustment  
- High speed mixture  
Carburetor adjustment  
- Idle speed  
Wear slip resis-  
tant foot wear.  
Safety/Alert  
Choke Control  
"Run"  
Position  
Choke Control  
"Cold Start"  
Position  
(Choke Open)  
(Choke Closed)  
DO NOT allow  
flames or sparks  
near fuel.  
DO NOT smoke  
near fuel.  
 
4
p e r s o n a l c o n d It Io n a n d s a f e t y e q u Ip m e n t  
WARNING  
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are  
not followed. Proper clothing and safety gear must be worn when operating unit.  
Proper Clothing  
Physical Condition  
Wear snug fitting, durable clothing;  
• Pants should have long legs, shirts with long sleeves.  
• DO NOT WEAR SHORTS,  
Your judgment and physical dexterity may not be good:  
• if you are tired or sick,  
• if you are taking medication,  
• DO NOT WEAR TIES, SCARVES, JEWELRY,  
or clothing with loose or hanging items that could  
become entangled in moving parts or surrounding  
growth.  
• if you have taken alcohol or drugs.  
Operate unit only if you are physically and mentally well.  
Eye Protection  
Wear eye protection that meets ANSI Z87.1 or CE re-  
quirements whenever you operate the unit.  
Breathing Protection  
Wear a facemask to protect against dust.  
Hand Protection  
Wear no-slip, heavy duty work gloves to improve your  
grip on the unit handles. Gloves also reduce the transmis-  
sion of machine vibration to your hands.  
Wear sturdy work shoes with nonskid soles;  
• DO NOT WEAR OPEN TOED SHOES,  
• DO NOT OPERATE UNIT BAREFOOTED.  
Wear no-slip, heavy duty work gloves.  
Keep long hair away from engine and air intake. Retain  
hair with cap or net.  
Hot Humid Weather  
Heavy protective clothing can increase operator fatigue  
which may lead to heat stroke. Schedule heavy work for  
early morning or late afternoon hours when temperatures  
are cooler.  
Hearing Protection  
ECHO recommends wearing hearing protection whenever  
unit is used.  
Vibration and Cold  
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be  
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-  
sations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended,  
because the minimum exposure which might trigger the ailment is unknown.  
• Keep your body warm, especially the head, neck, feet, ankles,  
hands, and wrists.  
• Maintain good blood circulation by performing vigorous arm  
exercises during frequent work breaks, and also by not smoking.  
• Limit the hours of operation. Try to fill each day with jobs where  
operating the trimmer or other hand-held power equipment is not  
required.  
• If you experience discomfort, redness and swelling of the fingers  
followed by whitening and loss of feeling, consult your physician  
before further exposing yourself to cold and vibration.  
 
Po w e r Bl o w e r At t A c h m e n t  
oP e r A t o r 's mA n u A l  
5
Repetitive Stress Injuries  
It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,  
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high  
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which  
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged  
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.  
To reduce the risk of RSI/CTS, do the following:  
• Avoid using your wrist in a bent, extended, or twisted position. In-  
stead, try to maintain a straight wrist position. Also, when grasping,  
use your whole hand, not just the thumb and index finger.  
• Take periodic breaks to minimize repetition and rest your hands.  
• Reduce the speed and force with which you do the repetitive move-  
ment.  
• Do exercises to strengthen the hand and arm muscles.  
• Immediately stop using all power equipment and consult a doctor if  
you feel tingling, numbness, or pain in the fingers, hands, wrists, or  
arms. The sooner RSI/CTS is diagnosed, the more likely permanent  
nerve and muscle damage can be prevented.  
DANGER  
Do not operate this product indoors or in inadequately ventilated  
areas. Engine exhaust contains poisonous emissions and can cause  
serious injury or death.  
Read the Manual  
• Provide all users of this equipment with the Operator's Manual for  
instructions on Safe Operation.  
Clear the Work Area  
• Spectators and fellow workers must be warned, and children and  
animals prevented from coming nearer than 15 m (50 ft.) while  
the unit is in use.  
• Take wind conditions into account: avoid open doors and win-  
dows.  
• Do not point blower at people or animals.  
• Review area to be cleared. Look for potential hazards such as  
stones or metal objects.  
Keep a Firm Grip  
• Hold the front and rear handles with both hands, with thumbs and  
fingers encircling the handles.  
Keep a Solid Stance  
• Maintain footing and balance at all times. Do not stand on slippery,  
uneven or unstable surfaces. Do not work in odd positions or on lad-  
ders. Do not over reach.  
Avoid hot Surfaces  
• Keep exhaust area clear of flammable debris. Avoid contact during  
and immediately after operation.  
 
6
e q u Ip m e n t  
WARNING  
Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachment  
combined with a non approved ECHO product.  
Before operation a complete check of the unit must be performed;  
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.  
• Do not use blower if any part is missing or damaged.  
• Have repairs done only by an authorized ECHO Service dealer.  
• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings.  
ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit.  
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.  
NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.  
 
Po w e r Bl o w e r At t A c h m e n t  
oP e r A t o r 's mA n u A l  
7
de s c r Ip t Io n  
Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the  
instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING  
instructions for specific information.  
1
2
Sound Label (located on blower housing)  
P/N X508000140  
71 Category III  
Measured at 50 ft. (15m) per ANSI B175.2  
General Warning Decal (located on blower housing)  
P/N X505002080  
1. DRIVE ShAFT ASSEMBLy – Lightweight aluminum drive shaft. 2-position shaft design permits unit to be ro-  
tated in 180-degree steps.  
2. BLOWER PIPE - Concentrates air stream.  
 
8
co n t e n t s  
The ECHO product you have purchased has been factory pre-assembled for your convenience.  
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing  
parts. Use the contents list to check for missing parts.  
_____ 1 - Power Blower Attachment  
_____ 1 - Operators Manual  
_____ 1 - Warranty Card  
_____ 1 - Storage Hook Assembly  
as s e m b l y  
p o w e r h e a d s h a f t /l o w e r s h a f t a s s e m b l y  
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.  
1. Set Power Head/Shaft Assembly on a level surface.  
B
2. Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock  
D
out position.  
3. Remove vinyl cap from attachment drive shaft.  
4. Remove cardboard spacer, if necessary.  
A
5. Carefully fit attachment lower drive shaft assembly into coupler (B)  
to decal assembly line (C), making sure that the inner lower drive  
shaft engages into the upper drive shaft mount.  
D
C
NOTE  
Earlier model Power Heads may have shorter couplings. Short  
couplings fit flush to decal point (E). New couplings are 4-3/4 in.  
long, and fit flush to line (C).  
A
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft  
hole. Insure locator pin is fully engaged by gently twisting  
lower drive shaft. Locator pin (A) should snap flush in coupler.  
Full engagement will prevent further shaft rotation.  
7. Secure lower shaft assembly to coupler by tightening clamping  
knob (D).  
E
 
Po w e r Bl o w e r At t A c h m e n t  
oP e r A t o r 's mA n u A l  
9
op e r a t Io n  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades  
and other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving.  
Wear gloves to protect hands from sharp edges and hot surfaces.  
o p e r a t In g b l o w e r  
WARNING  
Always wear safety glasses, hearing protection and a face fil-  
ter mask or serious personal injury may result. Do not point the  
blower pipe in the direction of people or pets.  
Read the Safety Section carefully.  
IMPORTANT  
To avoid engine damage due to over-revving, do not block blower  
pipe.  
1. Use only during appropriate hours.  
IMPORTANT  
Use reduced speed only when performing light-duty tasks or to  
comply with local noise regulations. Continuous low speed opera-  
tion may allow fuel/oil residue to build-up on the piston and cause  
rapid build-up of carbon on the spark arrestor screen, resulting  
in overheating and engine damage. To reduce harmful build-up,  
run engine at wide open throttle for at least 5 minutes every hour,  
and inspect/clean the spark arrestor screen after approximately 40  
hours of operation.  
2. Control blower speed with throttle trigger.  
3. Use lower speed to blow debris from hard surfaces.  
4. Additional speed may be necessary to clean debris, snow, etc.  
from lawns and flowerbeds.  
NOTE  
Never use a higher speed setting than necessary to perform a task.  
Remember, the higher the engine speed, the louder the blower  
noise. Minimize dust by using blower at lower speeds. Keep debris  
on your property.  
Be Smart - be a good neighbor.  
 
10  
ma In t e n a n c e  
WARNING  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.  
Wear gloves to protect hands from sharp edges and hot surfaces.  
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will  
help achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit  
to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the  
ECHO Dealer do it, each maintenance task has been graded.  
s k Il l l e v e l s  
Level 1 =  
Easy to do. Common tools may be required.  
Level 2 =  
Moderate difficulty. Some specialized tools may be required.  
m a In t e n a n c e In t e r v a l s  
Component  
Maintenance Procedure  
Skill Level  
Interval  
Screws/Nuts/Bolts  
Inspect/Tighten/Replace  
1
Before Each Use  
 
Po w e r Bl o w e r At t A c h m e n t  
oP e r A t o r 's mA n u A l  
11  
st o r a g e  
1. Store Power Blower attachment in a dry, dust free place out of the  
reach of children, using supplied storage hook.  
Storage Hook Installation  
1. Insert small end of hook into locating hole on attachment shaft.  
2. Slide plastic cap onto end of attachment shaft.  
sp e c If Ic a t Io n s  
MODEL ---------------------------------------------------- Power Blower Attachment  
Length ------------------------------------------------------- 635 mm (25.01 in.)  
Width -------------------------------------------------------- 231 mm (9.10 in.)  
Height ------------------------------------------------------- 212 mm (8.35 in.)  
Weight------------------------------------------------------- 1.76 kg (3.89 lbs.)  
Drive Shaft-------------------------------------------------- 6.35 mm (1/4 in.) Flex Shaft  
Maximum Air Speed (MPH) ----------------------------- 100 - 115 mph*  
Maximum Air Volume ------------------------------------ 317 - 364 cu. ft./min.*  
Sound Level at 50 ft. dB(A) scale per ANSI B175.2 - 71 dB(A)  
* Specifications are for a variety of power heads. Individual unit performance may vary.  
 
se r v Ic In g In f o r m a t Io n  
p a r t s /s e r Ia l n u m b e r  
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assem-  
blies for your ECHO products are available only from an Authorized  
ECHO Dealer. When you do need to buy parts always have the Model  
Number and Serial Number of the attachment with you. You can find  
these numbers on the driveshaft model/serial number label. For future  
reference, write them in the space provided below.  
Model No. _________________SN. ___________________  
DEALER?  
Call  
1-800-432-ECHO  
or  
s e r v Ic e  
Service of this product during the warranty period must be performed  
by an Authorized ECHO Service Dealer. For the name and address of  
the Authorized ECHO Service Dealer nearest you, ask your retailer or  
call: 1-800-432-ECHO (3246). Dealer information is also available on  
our Web Site. When presenting your unit for Warranty service/repairs,  
proof of purchase is required.  
CONSUMER PRODUCT  
SUPPORT  
1-800-673-1558  
8:30 - 4:30 Mon - Fri C.S.T.  
e c h o c o n s u m e r p r o d u c t s u p p o r t  
If you require assistance or have questions concerning the applica-  
tion, operation or maintenance of this product you may call the ECHO  
Consumer Product Support Department at 1-800-673-1558 from 8:30  
am to 4:30 pm (Central Standard Time) Monday through Friday. Before  
calling, please know the model and serial number of your unit.  
w a r r a n t y r e g Is t r a t Io n  
To ensure trouble free warranty coverage it is important that you regis-  
out the warranty registration card supplied with your unit. Registering  
your product confirms your warranty coverage and provides a direct  
link between you and ECHO if we find it necessary to contact you.  
a d d It Io n a l o r r e p l a c e m e n t m a n u a l s  
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-  
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the  
ECHO Web Site for updated information.  
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.  
echo, Incorporated  
400 oa k w o o d ro a d  
la k e Zu r Ic h , Il 60047-1564  
S68600001001/S68600999999  
 

Echo Trimmer GT 1100 User Manual
Eizo Computer Monitor L465 User Manual
Electro Voice Portable Speaker E V ONE User Manual
Extron electronic Speaker System SI 3 Black User Manual
Fagor America Cookware Double Boiler User Manual
Fisher Price Baby Toy T7164 User Manual
Fujitsu Scanner M3093EX User Manual
Gefen Network Router EXT HDKVM LAN User Manual
GE VCR VG4256 User Manual
Gitzo Camcorder Accessories GT2940L User Manual