Extron electronic Stereo Amplifier DA AV EQ User Manual

Setup Guide — DA AV EQ Series  
The Extron® DA AV EQ series are distribution amplifiers  
(DAs) that are available with composite video or S-video  
plus audio, audio only, and video only. They provide  
long cable drive capability and individual gain and  
equalization adjustment for each output pair. The two  
dual models can each be configured to function as two  
DAs.  
This guide provides basic instructions for an experienced installer to set up and operate these  
distribution amplifiers.  
Step 1 — Turn off and disconnect all equipment from power source  
Step 2 — Mount the unit (optional)  
If desired, mount the DA on a 9.5 inches deep or 6 inches deep rack shelf, or on furniture.  
Step 3 — Connect video devices (all models except DA 6A)  
Connect video input: Connect a composite video or an S-video source device to the Input  
connector. If using a DA 12V/6V or a DA 8V/4V in dual mode, connect input devices to the  
Input A and Input B connectors.  
Connect video output: Connect one or more video output devices to the composite video or  
S-video output connectors.  
Step 4 — Set dual mode toggle switch (Dual EQ models only)  
Set the toggle switch for dual or single mode as follows:  
INPUT A  
Dual mode: Set the toggle switch down to Dual 1x4 for the DA 8V/4V or  
Dual 1x6 for the DA 12V/6V, as shown at right. The DA functions as two  
1-input, 8- or 12-output DAs.  
1 x 12  
Single mode: Set the toggle switch up to 1x8 for the DA 8V/4V or 1x12  
for the DA 12V/6V. The DA functions as a 1-input, 8- or 12-output DA  
with active loop-through.  
LOOP-  
THRU  
Dual  
1 x 6  
INPUT B  
Step 5 — Connect monitor for loop-through (optional)  
Connect a monitor to the Loop-Thru connector for passive loop-through, if desired.  
For DA 12V/6V or DA 8V/4V Dual EQ models: If the DA will not be used in dual mode,  
connect a monitor to the Input B connector for active loop-through, if desired.  
Step 6 — Set termination toggle switch  
For all models except DA 6A, DA 12V/6V, and DA 8V/4V Dual EQ:  
INPUT  
If a monitor is connected to the Loop-Thru connector, set the Termination  
toggle switch up to high Z for passive loop-through, as shown at right.  
HIGH Z  
75 Ohm  
If no monitor is connected, set this switch down to 75 Ohm.  
LOOP-THRU  
Step 7 — Connect audio inputs  
Wire the captive screw or RCA input connectors to an audio source as shown below.  
Tip  
Sleeve  
Tip  
Ring  
Tip (+)  
Sleeve (s)  
Tip  
Tip  
Sleeve  
Ring  
Unbalanced Input  
Balanced Input  
Sleeve (  
)
RCA connector  
(Continued on reverse side)  
 

EAW Stereo Amplifier CAM80 User Manual
Eclipse Fujitsu Ten Car Stereo System CD3414 User Manual
Edimax Technology Network Router BR 6228NC V2 User Manual
Electro Voice Microphone 645TR User Manual
Estate Refrigerator 2316077B User Manual
Euro Pro Frozen Dessert Maker KP170H User Manual
Fisher Price Motorized Toy Car B0155 User Manual
Frigidaire Dishwasher FMB330RGC User Manual
Fujitsu Video Game Controller PG RMCU1 User Manual
GE Air Conditioner AGN05 User Manual